Ford Rear shudder when braking repair

Get quotes for your Ford from specialists near you

Otto
cancel
usp australia

Australia's #1 booking site for car services & car repairs

usp heart

Book now, pay later Interest-free payments

usp transparent fees

Transparent prices no surprises

  1. AutoGuru
  2. Repairs
  3. Ford
  4. Rear Shudder When Braking Repair

Average rating for Rear shudder when braking repair

starstarstarstarstar

5.0 • based on 1 review of 1 business

Buy now, pay later banners

*Available at select service providers. T&Cs apply.

Average rating for Rear shudder when braking repair

starstarstarstarstar

5.0 • based on 1 review of 1 business

Ford Rear shudder when braking repair

Why Does My Ford Have a Rear Shudder on Braking?

What is brake shudder? It manifests as a feeling of vibration through the steering wheel when braking. If you haven’t felt it, imagine the sensation you might feel if you drove over corrugated iron as you are braking in your Ford.

This vibration is more obvious when there is an issue with the front brakes because your hands are on the steering wheel which is connected to the front suspension. When there is a rear brake shudder it will still feel like a grab-and-release type of vibration, but it will be coming from the rear of your Ford and you will feel the pulsating sensation through the brake pedal.

The common culprit for rear brake shudder is uneven brake rotors (brake discs). This would only occur in vehicles with disc rotors on the rear as drum brakes don’t utilise rotors.

The experts have a name for uneven brake wear - disc thickness variation (DTV). When the brake caliper forces the brake pads against an uneven rotor, it creates variation in the brake torque. As there are higher and lower sections on a rotor affected with DTV, the brakes will grab and release, producing the pulsating that is felt through the brake pedal.

DTV can start to occur from the time new pads are fitted to your Ford. If brake bedding-in processes aren’t adopted it can create uneven wear on the rotor. It can also occur when the rotors are installed incorrectly. If for any reason the rotor is not flush with the surface it rests on, it will cause uneven rotation on the axis.

Another cause of DTV can be from the brake calipers. A brake caliper could be faulty, causing it to press the brake pad against the rotor when the brakes aren’t applied. This can cause uneven wear which is also a good reason why you should never casually rest your foot on the brake pedal whilst driving.

In some cases, the uneven wear can be caused by, or can also cause rotor runout. Rotor runout is when the brake rotor is off centre or has a wobble and is rotating off-axis. A faulty wheel bearing, buildup on the wheel hub/rotor hat that creates an uneven surface for the brake disc to sit on or badly tightened wheel lugs, can cause rotor runout.

When your car has DVT, the brake rotors will need to be replaced or machined. Machining is the process of removing a layer of the brake rotor to create a smooth surface. Brake rotors have a minimum required thickness and not all will rotors be able to be machined to alleviate DTV symptoms.

When repairing a rear brake shudder it may require more than just replacing or machining the faulty brake rotor/s. Make sure any underlying source of the DTV is found and fixed otherwise the same problem will continue to arise.

When there is an issue with your Ford's brakes you may notice:

  • Shudder that’s coming from the rear of the car when braking
  • Pulsating feeling through brake pedal on braking
  • Uneven brake rotors

When replacing brake components, remember to use a torque wrench when tightening wheel lugs. This will ensure even torque is applied to prevent rotor run out.

Take the time to bed in new brakes. If the brakes are not properly bedded in they can be subjected to thermal shock which can create uneven wear.

Make sure to clean the wheel hub of any buildup to create an even surface for the rotor to butt against.

It’s advised to fit new brake pads whenever brake rotors are replaced or machined.

Faulty brakes on your Ford are a danger to you and other road users and can, obviously, lead to very serious accidents - something you are sure to want to avoid.

When you're feeling a shudder from your brakes AutoGuru can provide a local brake expert for the job.

Ford Models

New Repairer? Join us Member Login

AutoGuru acknowledges and pays respects to the people of the Yugambeh language region of the Gold Coast where we are based and all their descendants both past and present. We also acknowledge the many Aboriginal and Torres Strait Islander ancestors of the land in which our network of auto service providers operate.